Extra-Long Spline Socket Bit
M10 x 800mm 1/2in.Dr
S2 Steel Bit with Chrome Vanadium Socket
For VAG Drive Shaft Bolts
Applicable to Audi / VW vehicles

Extra-Long Spline Socket Bit
M12 x 800mm 1/2in.Dr
S2 Steel Bit with Chrome Vanadium Socket
For VAG Drive Shaft Bolts
Applicable to Audi / VW vehicles

Extra-Long Spline Socket Bit
M14 x 800mm 1/2in.Dr
S2 Steel Bit with Chrome Vanadium Socket
For VAG Drive Shaft Bolts
Applicable to Audi / VW vehicles

6pc VAG Axle Nut Socket Set
Includes 14mm and 17mm Hex Bits
M18 Spline Bit and 24 | 30 | 32mm 12-Point Sockets.
1/2in. and 3/4in. Drive
Covers most 1996-2015 VW / Audi Front and Rear Axle Nuts.

8pc Drive Shaft Socket Set
Socket and Bit Set Specific for Drive Shafts
1/2in.Dr Hex Bits : 14 | 17 | 19mm
1/2in.Dr Deep Sockets : 27 | 30 | 32 | 34 | 36mm
Chrome-Molybdenum Steel

CV Boot Clamp Pliers
Crimps and flattens ear type clamps
CV Clamp Banding Tool
For installing CV Clamps
Standard banding tool for CV Joint Boots

CV Joint Boot Clamp Pliers - Ear Type
Ideal for installing clamps on fuel filters - waterpumps - CV joint boots and other cooling system hoses

CV Drive Shaft Boot Clamp Pliers
For Oetiker CV Drive Shaft boot Securing clips.
3/8in.Dr holes in the handle shafts to enable
a torque Wrench to be used with the tool when required.

CV Joint Boot Clamp Tool
For the assembly of Stainless Steel Bands
3/8in.Dr Jaws for use with a Torque Wrench
For torque sensitive rubber boot clamps

CV Joint Spring Ring Pliers
This tool is specifically designed to aid the secure removal
and re-installation of the CV Joint Spring Ring without damage.
With Unique jaws for holding the ring securely.
Length : 150mm
Jaw Capacity : 50mm

CV Boot Tool
For installing vehicle rubber CV boots without dismantling the CV joint.
Steel Centre / Plastic Composite Cone.
Diameter Size : 100mm Ex / 93mm Int.
Length : 405mm

Air Powered CV Boot Installation Tool
For the fast and efficient installation of uni-fit boots on the CV joint.
With air control switch to adjust fingers to the size of boot required.
Easily place the boot into place over CV joint.
The boot should be lubricated before each use.
Working pressure : 72-130psi
Air Inlet : 1/4in.

Air Powered Boot Installation Tool for CV Joints
Professional tool for commercial or occasional use.
Used for stretching flexible rubber CV boots
onto automatic drive shaft assemblies
Range : 20 - 110mm Diameter
Installs CV boots without removing axle.
Composite body with simple control valve.
For cars / small vans and light commercial vehicles.
1/4in. BSP inlet

7pc Drive Shaft Puller Set
230mm Long Puller with 120mm Housing
For BMW and VW Drive Shaft servicing

9/16in. Land Rover Prop Shaft Socket - 3/8in.Dr / 150mm
Suitable for
Defender : 90 | 110
Discovery : 1 | 2
Range Rover : P38

Will fit most makes and models of vehicles - except Seat.

Adjustable Seal Puller / 2 hook shapes
With rotating head for removing various oil and grease seals

3pc Seal Puller Set
Suitable for the safe damage free removal of Drive or Transmission Oil and Grease seals or O-rings.
Tool head shape provides better access than other seal pullers.

5pc 1/2in.Dr Castellated Socket Set - Mercedes
Gearbox / differential flange / front axles and bearings / rear axle drive flange
6 / 8mm Tooth x 70 / 80mm Long
For Mercedes G Class -
W-107 / 114 / 115 / 116 / 123 / 126 / 460 / 461 / 463
Chrome Molybdenum

5pc 1/2in.Dr Castellated Socket Set - Mercedes
Gearbox / differential flange / front axles and bearings / rear axle drive flange
6 / 8mm Tooth x 70 / 80mm Long
For Mercedes G Class -
W-107 / 114 / 115 / 116 / 123 / 126 / 460 / 461 / 463
Chrome Molybdenum